Why can I not switch gears when the car is on? I already replaced the clutch, FW, TOB and pressure plate, yet to no avail.
I replace the the clutch, Trow out bearing, pilot, fly wheel and pressure plate.
Nothing changed...
Your Answer:
Related Questions
-
Why can I not switch gears when the car is on? I already replaced the clutch, FW, TOB and pressure plate, yet to no avail. 2 Answers
I replace the the clutch, Trow out bearing, pilot, fly wheel and pressure plate. Nothing changed...
2008 Ford Mustang V6 Premium Coupe RWD
-
Maintenance & Repair
-
Why are the rpm shooting to the red when I smash the gas on takeoff? 1 Answer
I like to tend to try and accelerate really quick sometimes and it has been not doing what I want it to do. I used to have a truck and I could just hold down the gas and it would just book it and...
2004 Ford Mustang Coupe RWD
-
Maintenance & Repair
-
i have a 2000 ford mustang v6 guages went crazy when i backed up and the car died, put it park - restarted it. ran fine till i put in drive, guages bounced between max and minimum then it died again and now will not start. the remote trunk key chain - when i push to unlock the trunk or any of the other functions make the relays click under the dash. so is it my relays or something else 3 Answers
i have a 2000 ford mustang v6 guages went crazy when i backed up and the car died, put it park - restarted it. ran fine till i put in drive, guages bounced between max and minimum then it died again...
2000 Ford Mustang Coupe RWD
-
Maintenance & Repair
-
Fuseable link between ignition switch and solenoid keeps blowing. (Yellow Wire) car shuts down while driving. Starts when I replace the fuse. What do I do? 1 Answer
This all happened when I attempted to replace the ignition switch. I unplugged my battery. Then installed the switch. When I went to start it I heard a pop and small amount of smoke came from und...
1987 Ford Mustang GT Convertible
-
Maintenance & Repair
-
HELP!!!! 1. Is it better to take my original engine out of my car; resurface and rebuild or start over and buy a 302 engine...... 2. Can I use my 289 parts on the new 302? 1 Answer
I have a 1968 ford Mustang 289 engine bore out to a 302 with transmission that is trashed. My dad passed it on to me after 20 yrs of him flooring the hell out of it. I Want A Car With power but n...
1968 Ford Mustang Coupe RWD
-
Maintenance & Repair
Shortcuts
Search Ford Mustang Questions
CarGurus Experts
-
#1Gene ArnettReputation3,140
-
#2Bob BeamanReputation2,680
-
#3rst429Reputation2,600
Find great deals from top-rated dealers
SearchRelated Models For Sale
Used Dodge Challenger
23 Great Deals out of 768 listings starting at $11,480
Used Dodge Charger
44 Great Deals out of 856 listings starting at $5,995
Used Chevrolet Corvette
26 Great Deals out of 786 listings starting at $15,900
Used Ford Mustang Shelby GT500
6 Great Deals out of 38 listings starting at $34,895
Used Ford F-150
305 Great Deals out of 13,473 listings starting at $3,888
Used BMW 3 Series
66 Great Deals out of 1,169 listings starting at $2,500
Used BMW M3
10 Great Deals out of 81 listings starting at $14,995
Used Chevrolet Silverado 1500
167 Great Deals out of 7,420 listings starting at $6,995
Used Honda Civic
185 Great Deals out of 4,025 listings starting at $2,877
Used Jeep Wrangler
143 Great Deals out of 5,937 listings starting at $2,995
Used Toyota Camry
49 Great Deals out of 1,094 listings starting at $2,500
Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.