Can a drivers module fuel pump be clog ? Causing vehicle to stall, as if no pressure when accelerating.

Asked by Precious Jun 25, 2015 at 05:01 PM

Question type: Maintenance & Repair

2001 Ford Expedition, stalling when accelerating( new fuel pump and filters, recent
tuneup, new muffler)

64,530

firebird338 answered 8 years ago

Check air filter and also clean throttle body with throttle body cleaner spray add throttle body cleaner to gas tank then take out on road and hit your passing gear a few times this well clear out the carbon build up. Be careful no speeding tickets.

1 people found this helpful.

Mark helpful

Your Answer:

Can a drivers module fuel pump be clog ? Causing vehicle to stall, as if no pressure when accelerating. 1 Answer

2001 Ford Expedition, stalling when accelerating( new fuel pump and filters, recent tuneup, new muffler)

Maintenance & Repair
I have a 1999 Chevy Blazer, 4x4, 4.3 vortec. We have changed the coil pack, fuel filter, distributor cap and button, the crank shaft sensor, cam sensor and plug wires as well as the ignition control module. We coming to a stop sign it will stall and sometimes when just sitting still. Sometimes it will start right back up and other times it takes several tries. I also have the oxygen sensor on order and it should be here tomorrow. Fuel pressure tested perfectly. No black smoke, no smell of rotten eggs or the cat glowing red. The only code that comes up is PO420. 4 Answers

I have a 1999 Chevy Blazer, 4x4, 4.3 vortec. We have changed the coil pack, fuel filter, distributor cap and button, the crank shaft sensor, cam sensor and plug wires as well as the ignition control m...

1999 Chevrolet Blazer 4-Door 4WD

-

Maintenance & Repair
1999 Honda CR-V will not start. I changed the fuel pump, fuel pressure regulator along with the fuel filter and the main relay but the vehicle still will not start. The distributor along with the coil was replaced about two months ago, spark is ok. Sometimes the vehicle start for a few second but the engine stalls as if the timming is off but the timing is ok, also sometimes it back fires and when it does the vacuum hose that is connected to the fuel pressure regulator comes off from the regulator. I check the injectors and they are getting power. I disconnected the exhaust thinking of the catalytic but still no start. Could it be the computer? Any help on this matter will be greatly appreciated. Thanks 8 Answers

1999 Honda CR-V will not start. I changed the fuel pump, fuel pressure regulator along with the fuel filter and the main relay but the vehicle still will not start. The distributor along with the coil...

1999 Honda CR-V

-

Maintenance & Repair
My '92 Caprice Classic will run fine for a day and then will stall and die at a stop. Sometimes c an restart, bvut often have to remove the breather, start it, put the breather back on. Also stalls when making turns. Air filter is good, I removed it and tried to start but no go. Have to remove the breather, start it, and then put it back on. Has a new distibuter, control module, fuel pump, fuel filter, oil pressure sesnsor, egr vale and solenoid. What might cause this? 4 Answers

My '92 Caprice Classic will run fine for a day and then will stall and die at a stop. Sometimes c an restart, bvut often have to remove the breather, start it, put the breather back on. Also stal...

1992 Chevrolet Caprice Classic Sedan RWD

-

Maintenance & Repair
what could be causing the vehicle to stall when it is put into drive or reverse 1 Answer

This only happens when the vehicle is cold. once the engine has warmed up for about ten minutes, the vehicle will stay running in drive and reverse. its just when the car is in reverse, it sounds pret...

1992 Dodge Colt 2 Dr GL Hatchback

-

Maintenance & Repair

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.