I've got a 96 ranger xlt with the slave cylinder, throw out bearing built in the back of bell housing, my clutch is working,going in all the gears but whenever I give it gas it grinds like the splines

Asked by Patrick Sep 17, 2014 at 03:30 AM

Question type: Maintenance & Repair

Are stripped ,do you think my shaft or transmission is stripped
It will run in all gears but slips ,grinds really bad

62,785

BoholMark answered 9 years ago

If it's slipping then I think it is the clutch. If it's grinding when you are going down the road then it's the transmission. Have you checked the transmission oil? Let us know.

Mark helpful

Your Answer:

I've got a 96 ranger xlt with the slave cylinder, throw out bearing built in the back of bell housing, my clutch is working,going in all the gears but whenever I give it gas it grinds like the splines 1 Answer

Are stripped ,do you think my shaft or transmission is stripped It will run in all gears but slips ,grinds really bad

Maintenance & Repair
04 gmc sierra 1500 5.3 died on me on the highway got it towed home starting going at it, hooked two different scanners to it and not throwing any codes (ecm is working bc the map was reading correctly but also the rpm was zero) anyways checked fire none checked injectors they wasnt working either(built fuel pressure then unplugged fuel relay then turned engine over and the pressure stayed the exact same) i assume it might be the crank sensor but i would think it would throw a code, anyways came back this morning and before doing anything for the hell of it i checked the gas cap and tightened it and it fired up perfect three different times and the last time i let it run and it died after bout 45 seconds (fuel pressure reads 55) and after it died its doing the same thing cranks but wont fire or start 1 Answer

died on me on the highway got it towed home starting going at it, hooked two different scanners to it and not throwing any codes (ecm is working bc the map was reading correctly but also the rpm was...

2004 GMC Sierra 1500

-

Maintenance & Repair
i put a new ignition switch in my truck but to do it i took apart the top of the column to do so and when i did a piece fell out with a spring and i got it to where it all goes back and i don't know where the spring looking thing goes and now it is like the key aint telling the transmition its on because it wont go into gear it wont shift out of park 5 Answers

this si my everyday driver i need it fixed asap

1986 Ford F-150 XL Extended Cab LB

-

Maintenance & Repair
I have a 96 Ford ranger, 4 cylinder manual and have a problem I can't figure out. I can start the truck every time with no problem it isles great and I can sit there and rev it all day no problem but if I go to drive it I can make it about 1/2 mile and then that's it, ill press the gas petal and it won't do any thing but kill the gas (no gas) but soon as I take my foot off the gas it will idle just fine and rev fine but won't go anywhere unless I let it sit for a few mins and it will start all over. I have replaced the IAC, TPS and today the external fuel filter that was clogged but same thing. Once in a while if I push the clutch in it will stay at a rev for a sec. Please help 5 Answers

96 Ford ranger need help :(

1996 Ford Ranger XL Standard Cab SB

-

Maintenance & Repair
My 2004 Mini non-S with 150,000 miles starting doing something funny last week. When I try to activate a left or right turn signal, there is no flashing of the green indicator light or clicking in the car, but the lights themselves are working outside the car. And then, the other day the dash indicator lights in the car went out and then came back in a few minutes. The problem is intermittent, but is getting worse. If I turn the car off for a few minutes it all seems to come back. I'm hoping someone can diagnose it. 1 Answer

My 2004 Mini non-S with 150,000 miles starting doing something funny last week. When I try to activate a left or right turn signal, there is no flashing of the green indicator light or clicking in the...

2004 MINI Cooper Base

-

Maintenance & Repair

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.