What is the drive cycle sequence for a 2007 Hyundai Santa Fe?

10

Asked by guzmanway Aug 04, 2014 at 02:53 PM about the 2007 Hyundai Santa Fe 2.7L GLS FWD

Question type: Maintenance & Repair

I just changed both Right and Left fuel sender units and erased the codes.

2 Answers

10

Sallybg asked the same question on Mar 06, 2013 for a 2008 Santa Fe. Judge_roy responded. His solution also worked on my 2007 Santa Fe. His response/solution was as follows: To perform an OBDII Driving cycle do the following: Cold Start. In order to be classified as a cold start the engine coolant temperature must be below 50°C (122°F) and within 6°C (11°F) of the ambient air temperature at startup. Do not leave the key on prior to the cold start or the heated oxygen sensor diagnostic may not run. Idle. The engine must be run for two and a half minutes with the air conditioner on and rear defroster on. The more electrical load you can apply the better. This will test the O2 heater, Passive Air, Purge "No Flow", Misfire and if closed loop is achieved, Fuel Trim. Accelerate. Turn off the air conditioner and all the other loads and apply half throttle until 88km/hr (55mph) is reached. During this time the Misfire, Fuel Trim, and Purge Flow diagnostics will be performed. Hold Steady Speed. Hold a steady speed of 88km/hr (55mph) for 3 minutes. During this time the O2 response, air Intrusive, EGR, Purge, Misfire, and Fuel Trim diagnostics will be performed. Decelerate. Let off the accelerator pedal. Do not shift, touch the brake or clutch. It is important to let the vehicle coast along gradually slowing down to 32km/hr (20 mph). During this time the EGR, Purge and Fuel Trim diagnostics will be performed. Accelerate. Accelerate at 3/4 throttle until 88-96 km/hr (55-60mph). This will perform the same diagnostics as in step 3. Hold Steady Speed. Hold a steady speed of 88km/hr (55mph) for five minutes. During this time, in addition to the diagnostics performed in step 4, the catalyst monitor diagnostics will be performed. If the catalyst is marginal or the battery has been disconnected, it may take 5 complete driving cycles to determine the state of the catalyst. Decelerate. This will perform the same diagnostics as in step 5. Again, don't press the clutch or brakes or shift gears. Reprinted on OBDII web site courtesy of General Motors Corporation is this what you are asking?

This think worked on my 2007 Hyundai Santa Fe, thanks for your post, saved me time and money. Thank you.

Your Answer:

CarGurus Experts

  • #1
    me29
    Reputation
    6,540
  • #2
    JP1956
    Reputation
    2,810
  • #3
    SubaruTech5862
    Reputation
    2,010
View All

Find great deals from top-rated dealers

Search

Related Models For Sale

Used Hyundai Tucson
93 Great Deals out of 2,515 listings starting at $2,450
Used Kia Sorento
73 Great Deals out of 1,712 listings starting at $1,500
Used Honda CR-V
157 Great Deals out of 4,953 listings starting at $440
Used Toyota RAV4
111 Great Deals out of 2,857 listings starting at $2,949
Used Toyota Highlander
37 Great Deals out of 814 listings starting at $8,495
Used Honda Pilot
33 Great Deals out of 792 listings starting at $2,495
Used Hyundai Sonata
51 Great Deals out of 824 listings starting at $3,995
Used Nissan Rogue
127 Great Deals out of 4,950 listings starting at $3,495
Used Ford Explorer
53 Great Deals out of 2,231 listings starting at $7,990
Used Kia Sportage
58 Great Deals out of 1,933 listings starting at $3,999

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.