Exaust pipe broken at manifold. It is fully separated. Is it too late to weld? Is there a slip or sleeve I can install and clamp or weld for a temp fix? Do I need to completely replace the manifold peice and perhaps a complete exaust, catalytic converter and muffler?

Asked by Maxxi Jan 28, 2020 at 05:05 AM about the 2001 Ford Mustang

Question type: Maintenance & Repair

Need tips and repair advice

F_O_R answered 4 years ago

Have a muffler shop look at it.

Mark helpful

Your Answer:

Exaust pipe broken at manifold. It is fully separated. Is it too late to weld? Is there a slip or sleeve I can install and clamp or weld for a temp fix? Do I need to completely replace the manifold peice and perhaps a complete exaust, catalytic converter and muffler? 1 Answer

Need tips and repair advice

2001 Ford Mustang

-

Maintenance & Repair
what transmission will fit my 98 mustang with a 3.8l v6 it has a blown t5 and i want to replace it will a 01 tv work or is there to big of a diferance 3 Answers

yesterday my 97 t5 manual trans dropped every gear but 4th so im lokiong for a replacement and i cant find anything on 96-98 mustan g v6 trans

1997 Ford Mustang Convertible RWD

-

Maintenance & Repair
HELP!!!! 1. Is it better to take my original engine out of my car; resurface and rebuild or start over and buy a 302 engine...... 2. Can I use my 289 parts on the new 302? 1 Answer

I have a 1968 ford Mustang 289 engine bore out to a 302 with transmission that is trashed. My dad passed it on to me after 20 yrs of him flooring the hell out of it. I Want A Car With power but n...

1968 Ford Mustang Coupe RWD

-

Maintenance & Repair
i have a 2000 ford mustang v6 guages went crazy when i backed up and the car died, put it park - restarted it. ran fine till i put in drive, guages bounced between max and minimum then it died again and now will not start. the remote trunk key chain - when i push to unlock the trunk or any of the other functions make the relays click under the dash. so is it my relays or something else 3 Answers

i have a 2000 ford mustang v6 guages went crazy when i backed up and the car died, put it park - restarted it. ran fine till i put in drive, guages bounced between max and minimum then it died again...

2000 Ford Mustang Coupe RWD

-

Maintenance & Repair
I'm trying to fix the heater in my 1966 Ford Mustang, and I read in an answer on here concerning the switches for the heater "Also all 3 of those control levers are hooked to cables. Look under the dash and check to make sure those cables are connected and not broken. Sometimes they stiffen up and break." If one of these (the one reading "heat") were broken, would it stop the heater from starting even though all the other parts are working? And if so, what solution is there to reaffix the switch to its respective cable? 1 Answer

Attempting to fix a 1966 Ford Mustang's heater. One of the switches inside of the car is disconnected from its cable, which has broken. What's the fix?

1966 Ford Mustang Coupe RWD

-

Maintenance & Repair

Used Chevrolet Camaro

14 Great Deals out of 468 listings starting at $10,995

Used Chevrolet Corvette

16 Great Deals out of 722 listings starting at $10,989

Used Ford F-150

325 Great Deals out of 13,693 listings starting at $3,800

Used BMW 3 Series

67 Great Deals out of 1,211 listings starting at $2,500

Used Ford Mustang SVT Cobra

7 listings starting at $25,000

Used Chevrolet Silverado 1500

200 Great Deals out of 8,052 listings starting at $1,500

Used BMW M3

6 Great Deals out of 71 listings starting at $14,995

Used Honda Civic

192 Great Deals out of 4,047 listings starting at $440

Used Jeep Wrangler

142 Great Deals out of 5,984 listings starting at $6,500

Used Toyota Camry

44 Great Deals out of 1,134 listings starting at $4,795

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.

Exaust pipe broken at manifold. It is fully separated. Is it too late to weld? Is there a slip or sleeve I can install and clamp or weld for a temp fix? Do I need to completely replace the manifold peice and perhaps a complete exaust, catalytic converter and muffler?

1 Answer

Your Answer:

Shortcuts

Search Ford Mustang Questions

CarGurus Experts

Find great deals from top-rated dealers

Related Models For Sale

Exaust pipe broken at manifold. It is fully separated. Is it too late to weld? Is there a slip or sleeve I can install and clamp or weld for a temp fix? Do I need to completely replace the manifold peice and perhaps a complete exaust, catalytic converter and muffler?

1 Answer

Your Answer:

Related Questions